17 More Must-Know Data Science Interview Questions and Answers

There are 17 questions from KDnuggets but I will summarize the key contents below:

Minimizing total model error relies on the balancing of bias and variance errors. Ideally, models are the result of a collection of unbiased data of low variance. Unfortunately, however, the more complex a model becomes, its tendency is toward less bias but greater variance; therefore an optimal model would need to consider a balance between these 2 properties.

What are some ways I can make my model more robust to outliers?

Outliers are usually defined in relation to the distribution. Thus outliers could be removed in the pre-processing step (before any learning step), by using standard deviations (for normality) or interquartile ranges (for not normal/unknown) as threshold levels.

Moreover, data transformation (e.g. log transformation) may help if data have a noticeable tail. When outliers related to the sensitivity of the collecting instrument which may not precisely record small values, Winsorization may be useful. This type of transformation (named after Charles P. Winsor (1895–1951)) has the same effect as clipping signals (i.e. replaces extreme data values with less extreme values).  Another option to reduce the influence of outliers is using mean absolute difference rather mean squared error.

What is overfitting and how to avoid it?

Several methods can be used to avoid “overfitting” the data:

  • Try to find the simplest possible hypothesis
  • Regularization (adding a penalty for complexity)
  • Randomization Testing (randomize the class variable, try your method on this data – if it find the same strong results, something is wrong)
  • Nested cross-validation  (do feature selection on one level, then run entire method in cross-validation on outer level)
  • Adjusting the False Discovery Rate
  • Using the reusable holdout method – a breakthrough approach proposed in 2015

How can you determine which features are the most important in your model?

Feature selection approach

 

When can parallelism make your algorithms run faster? When could it make your algorithms run slower?

The performance of parallelism against sequential computing is largely determined by how the time consumed by this overhead compares to the time saved due to parallelization.

A widely-known theoretical approach to assessing the benefit of parallelization is Amdahl’s law, which gives the following formula to measure the speedup of running sub-tasks in parallel (over different processors) versus running them sequentially (on a single processor):

where:

  • Slatency is the theoretical speedup of the execution of the whole task;
  • s is the speedup of the part of the task that benefits from improved system resources;
  • is the proportion of execution time that the part benefiting from improved resources originally occupied.

To understand the implication of Amdahl’s Law, look at the following figure that illustrates the theoretical speedup against an increasing number of processor cores, for tasks with different level of achievable parallelization:

Speedup by number of cores

It is important to note that not every program can be effectively parallelized. Rather, very few programs will scale with perfect speedups because of the limitations due to sequential portions, inter-communication costs, etc. Usually, large data sets form a compelling case for parallelization. However, it should not be assumed that parallelization would lead to performance benefits. Rather, the performance of parallelism and sequential should be compared on a sub-set of the problem, before investing effort into parallelization.

In unsupervised learning, if a ground truth about a dataset is unknown, how can we determine the most useful number of clusters to be?

The Elbow Method

Elbow method

The Silhouette Method

The silhouette method measures the similarity of an object to its own cluster — called cohesion — when compared to other clusters — called separation. The silhouette value is the means for this comparison, which is a value of the range [-1, 1]; a value close to 1 indicates a close relationship with objects in its own cluster, while a value close to -1 indicates the opposite. A clustered set of data in a model producing mostly high silhouette values is likely an acceptable and appropriate model.

Silhouette method 

 

Ref:

https://www.kdnuggets.com/2017/02/17-data-science-interview-questions-answers.html

 

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

%d bloggers like this: